Simplus Stand Garment Steamer GTJH025 User Manual

Ⅰ. Product Parameters

Ⅱ. Product Illustration

① Steam nozzle

② Nozzle bracket 1

③ Ironing board

④ Steam hose

⑤ Switch

⑥ Base

⑦ Clothes hanger

⑧ Clamp

⑨ Height adjustment rod

⑩ Clamp

⑪ Water tank

⑫ Drain nut

⑬ Nozzle bracket 2

Ⅲ. Operation Instruction

Installation Instructions

Note: Do not connect to power before installation.

1. Insert the flat side of the lift rod into the front of the main unit. Open the clips on the first and second sections, extend them, and secure them tightly.

Note: To retract the lift rod: Open the clips on the first and second sections, fully retract the rod, secure the clips, then pull it out.

2. Align the nozzle bracket with the hanger's fixed slot and snap it into place. Insert the hanger with the nozzle bracket attached into the top of the lift rod and secure the clips.
3. Insert the steam hose into the main unit's port. Press firmly and turn the knob clockwise to lock it in place.

4. Finally, hang the nozzle on the nozzle bracket to complete installation.

Ironing Board Installation Instructions

1. Remove the ironing board from its packaging.

① Horizontal ironing bracket

② Vertical ironing bracket

2. For horizontal ironing, align the horizontal bracket with the topmost position of the lift rod and insert it.

3. For vertical ironing, align the vertical bracket with the lift rod of the hanger and snap it into place.

Instructions for Use

1. Fill the water tank completely and tighten the tank cap securely.

Note: Use distilled or purified water only. Do not add any detergents, essential oils, or chemical agents.

2. Plug in the power cord, turn the switch knob to power on the machine, and select the appropriate setting.

3. Wait briefly—approximately 25 seconds for low heat and 60seconds for high heat—until high-temperature steam is emitted. You may then begin ironing garments.

Caution:

1. When ironing flat on the ironing board, adjust the lift rod to position the board 80cm above the ground. A “gurgling” sound during low-height ironing is normal. If this occurs, briefly raise the spray head before continuing.
2. When raising the nozzle, steam may suddenly flow freely and expel water droplets. Exercise caution for safety!
3. Never direct steam toward people, animals, or flammable items.
4. Do not iron clothing while it is being worn.
5. Take care to prevent steam splashes during operation.
6. Ensure the appliance is fully preheated before activating steam function to prevent water leakage.
7. During ironing, never touch the high-temperature steam or steam panel with your hands.
8. Do not place the steam hose on the ground or kink it. Never disconnect the hose during use. If removal is necessary, first unplug the power to prevent burns. Allow the hose to cool to room temperature and ensure no water remains inside before disassembly.
9. Do not place the appliance directly on surfaces made of heat-sensitive materials such as glass to avoid hazards.

Ⅳ ． Cleaning and Maintenance

1. Before cleaning, unplug the power cord and allow the unit to cool for at least 30 minutes.
2. Remove the water tank, unscrew the tank knob, pour out the water, then rinse with clean water.
3. After completely draining the water, reinstall the tank into the main unit.
4. Unscrew the drain plug at the bottom of the main unit. Place a basin underneath to catch the water, drain the unit completely, then tighten the drain plug securely.
5. Wipe the exterior with a damp cloth. Never submerge the entire unit in water or rinse it under a faucet.
6. Never pour hot water or corrosive cleaning agents into the water tank, as this will damage the machine.
7. When storing, drain the water tank completely and allow all components to air dry before storage.
8. For long-term storage, keep the product in a dry, cool place away from dust, high temperatures, and direct sunlight.

Ⅴ . Cautions

To ensure safety, this product complies with all applicable standards and regulations. Before using this product, please read this manual carefully and keep it for future reference.

1. This product is not intended for use by persons with physical, cognitive, or mental impairments, or lack of knowledge or experience, including children, unless under the direct supervision and guidance of a responsible adult.
2. Keep this product out of reach of children.
3. Before use, verify that the rated voltage matches your local power supply. Use only the original or manufacturer-specified power cord and charger.
4. Do not use if the plug, power cord, or product shows damage, cracks, or electrical leakage. Do not disassemble or modify the product. Contact customer service immediately if abnormalities occur.
5. Do not plug or unplug the power cord or operate the device with wet hands.
6. If smoke, unusual odors, excessive heat, or deformation occur during operation or charging, immediately disconnect the power and cease use. Contact customer service if necessary.
7. This product is for household use only. Commercial, professional, or unauthorized use beyond the specified functions is prohibited. Failure to follow the manual voids the warranty, and the manufacturer assumes no liability for damages.
8. This product must be used under supervision. Never leave the device operating unattended. Disconnect power when leaving the area, during assembly/disassembly, cleaning, or maintenance.
9. Avoid direct skin contact with high-temperature components. Exercise caution to prevent burns.
10. Fill the tank with cold water before use. Never add hot water, as it may cause deformation. Monitor water levels regularly during operation.
11. Before filling or draining water, disconnect the power supply. Avoid splashing water.
12. Before cleaning, moving the unit, or when not in use, turn off the power and unplug the unit before proceeding.
13. Never place the machine near flammable items.
14. Keep the steam hose and nozzle above waist level at all times to ensure smooth steam flow. Failure to do so may cause gurgling noises. Never insert any objects into the steam hose or nozzle opening.
15. Non-original accessories may cause fire, electric shock, or damage to the machine.
16. Residual moisture or water droplets in the water tank may be present due to factory quality testing. This is normal and does not affect usage.

VI. Common Problem